Horizontal drilling

From Wikimarcellus

(Difference between revisions)
Jump to: navigation, search
Revision as of 00:59, 2 November 2008
Tcopley (Talk | contribs)

← Previous diff
Current revision
Tcopley (Talk | contribs)

Line 1: Line 1:
-In order to tap natural gas with '''horizontal drilling''' typically a drill is sent down vertically a mile or so underground and then turned at a ninety degree angle horizontally into the shale. By using horizontal drilling the drill bit can penetrates a much greater number of pockets of natural gas than it ever could with vertical drilling. On the average horizontal wells produce three to five times the amount of natural gas from vertical ones.+[[Image:horiz_rig.gif|frame|right|<div align="center">'''Horizontal Drilling Rig - Greene Co., PA'''.<br> Photo courtesy of [http://www.energycorporationofamerica.com/ Energy Corp. of America]</div>]]
 +'''Horizontal drilling''' is a form of ''directional drilling''. In order to tap the natural gas, typically a drill is sent down vertically a distance up to a mile or so underground and then turned at a ninety degree angle horizontally into the shale. Specialized drilling rigs are commonly used for each of the vertical and horizontal segments of the well. By using horizontal drilling, the drill bit can penetrate a much greater number of pockets of natural gas than it ever could with [[vertical drilling]]. On the average, horizontal wells produce three to five times the amount of natural gas that vertical ones do.
-The shale tends to be located between approximately five and eight thousand feet below ground.+[[Marcellus shale]] tends to be located between approximately five and eight thousand feet below ground although it can be at even greater depth.
-Horizontal wells are much more expensive to drill than vertical ones. Costs may run between $4 million and $7 million U.S. for a horizontal shale well. Vertical wells can be drilled for only $1-2 million U.S.+Layers of natural gas-bearing shale lay on ''horizons'' – these are the rock formations arrayed like stacked pancakes--one on top of the next. Greater well bore exposure to a formation such as the Marcellus or [[Utica shale|Utica]] shale can be achieved by turning the drill bit into a horizon and then drilling sideways rather than merely vertically. Shale gas tends to be trapped in exceedingly small pockets and joints in the shale rock which cannot be efficiently released from formation until the well subsequently is [[hydro-fracturing|hydro-fractured]].
-Reusable drilling rigs that cost up to $16 million apiece are generally used for horizontally drilling [[Marcellus shale]] wells.+Horizontal drilling rigs can drill down up to 10,000 feet vertically to the Marcellus or other shale, and then turn horizontally for a few thousand additional feet. The horizontal portion of the well bore is referred to as a ''lateral''. Well pads are around 5 acres with up to 6 horizontal wells stemming from the [[Pad drilling|same pad]].
 + 
 +Horizontal wells are much more expensive to drill than vertical ones. Costs may run between $4 million and $7 million U.S. for a horizontal shale well. Vertical [[Marcellus shale]] or [[Trenton-Black River]] wells can be drilled for only $1-2 million U.S. Shallow vertical wells can be drilled for even a lot less money.
 + 
 +Reusable drilling rigs that cost up to $16 million apiece are generally used for horizontally drilling [[Marcellus shale]] wells. These rigs are larger-sized ones with 1,000 and 1,600 horsepower. Newer ones with ''crawlers'' can be moved around the well pad for drilling multiple wells. [[Range Resources]] has been one of the industry leaders in introducing new rig technology.
 + 
 +A business strategy sometimes employed is to drill a vertical well. This can be done fairly inexpensively to get some scientific data about the acreage, and then go back in later with a horizontal portion of the well using a larger rig.
 + 
 +==Resources==
 + 
 +*[http://en.wikipedia.org/wiki/Directional_drilling - ''Wikipedia'' on directional drilling]
 +*[http://www.chiefog.com/drilling_process.html - Video on horizontal drilling] and [[Hydro-fracturing|hydro-fracturing]] produced by [[Chief Oil and Gas]].
 + 
 +[[Category:Drilling practices]]

Current revision

Horizontal Drilling Rig - Greene Co., PA. Photo courtesy of Energy Corp. of America
Horizontal Drilling Rig - Greene Co., PA.
Photo courtesy of Energy Corp. of America

Horizontal drilling is a form of directional drilling. In order to tap the natural gas, typically a drill is sent down vertically a distance up to a mile or so underground and then turned at a ninety degree angle horizontally into the shale. Specialized drilling rigs are commonly used for each of the vertical and horizontal segments of the well. By using horizontal drilling, the drill bit can penetrate a much greater number of pockets of natural gas than it ever could with vertical drilling. On the average, horizontal wells produce three to five times the amount of natural gas that vertical ones do.

Marcellus shale tends to be located between approximately five and eight thousand feet below ground although it can be at even greater depth.

Layers of natural gas-bearing shale lay on horizons – these are the rock formations arrayed like stacked pancakes--one on top of the next. Greater well bore exposure to a formation such as the Marcellus or Utica shale can be achieved by turning the drill bit into a horizon and then drilling sideways rather than merely vertically. Shale gas tends to be trapped in exceedingly small pockets and joints in the shale rock which cannot be efficiently released from formation until the well subsequently is hydro-fractured.

Horizontal drilling rigs can drill down up to 10,000 feet vertically to the Marcellus or other shale, and then turn horizontally for a few thousand additional feet. The horizontal portion of the well bore is referred to as a lateral. Well pads are around 5 acres with up to 6 horizontal wells stemming from the same pad.

Horizontal wells are much more expensive to drill than vertical ones. Costs may run between $4 million and $7 million U.S. for a horizontal shale well. Vertical Marcellus shale or Trenton-Black River wells can be drilled for only $1-2 million U.S. Shallow vertical wells can be drilled for even a lot less money.

Reusable drilling rigs that cost up to $16 million apiece are generally used for horizontally drilling Marcellus shale wells. These rigs are larger-sized ones with 1,000 and 1,600 horsepower. Newer ones with crawlers can be moved around the well pad for drilling multiple wells. Range Resources has been one of the industry leaders in introducing new rig technology.

A business strategy sometimes employed is to drill a vertical well. This can be done fairly inexpensively to get some scientific data about the acreage, and then go back in later with a horizontal portion of the well using a larger rig.

Resources

Personal tools